FD series units are primarily used in applications needing rapid drying and sterilization. Totally homogenous temperature distribution, rapid dynamic response, and a special air turbine which was developed by us and has 20 % higher output, have made the FD series a genuine time-saving device.
Important characteristics
Temperature range: ambient temperature plus 10 °C to 300 °C
Up to 30% lower energy consumption compared to conventional units on the market
High temperature accuracy thanks to APT.line™ technology
Forced convection
Controller with LCD display
Electromechanical control of the exhaust air flap
2 chrome-plated racks
Stackable
Class 2 integrated independent adjustable temperature safety device (DIN 12880) with visual alarm
Ergonomic handle design
USB port for recording data
Features:
Electronically controlled APT.line™ preheating chamber assuring temperature accuracy and reproducible results
Temperature range 5 °C (32 ºF) above ambient temperature up to 300 °C (572 °F)
DS controller with integrated timer 0 to 99 h
Digital temperature setting with an accuracy of one degree
Independent adjustable temperature safety device class 2 (DIN 12880), with visual temperature alarm
Adjustable front ventilation flap slide and rear exhaust ø 50 mm (1.97 inch)
Units up to 115 liters are stackable
2 chrome-plated racks included
BINDER test certificate
Options
Access port with silicone plugs, 10 mm (0.39 inch), 30 mm (1.18 inch), 50 mm (1.97 inch), 100 mm (3.94 inch)
Independent adjustable temperature safety device, Class 3.1 (DIN 12880)
Analog temperature output, 4 - 20 mA, with 6 - pin DIN socket (output not adjustable)
Over temperature alarm, acoustic, can be switched off. Temperature limit can be set at the independent, adjustable temperature safety device class 2
Anti-slip rubber pads for safe stacking (4 pieces)
Temperature measurement acc. to DIN 12880 (27 measuring points) at 150 °C (302 °F) or at specified temperature with measuring protocol and certificate
Factory calibration certificate. Measurement in center of chamber at 150 °C (302 °F) or at specified testing temperature
Extension to factory calibration certificate. Each additional measurement at an additional measuring point or temperature
Rack, chrome - plated or stainless steel
Shelf, perforated, stainless steel
Lockable door
FKM door gasket
Door with window and interior lighting, 15 W (320 x 260 mm / 12.60 x 10.24 inch)
Plus door handle, I-panel and exhaust duct (mm/inch) 105 / 4.1
Wall clearance rear (mm/inch) 100 / 3.9
Wall clearance side (mm/inch) 160 / 6.3
Exhaust duct outer- Ø (mm/inch) 52 / 2.1
Steam space volume (l/cu.ft.) 158 / 5.6
Number of doors 1
Interior dimensions
Width (mm/inch) 600 / 23.6
Height (mm/inch) 480 / 18.9
Depth (mm/inch) 400 / 15.8
Interior volume (l/cu.ft.) 115 / 4.1
Racks, chrome-plated (number standard/max.) 2 / 6
Load per rack (kg/lbs.) 20 / 44
Permitted total load (kg/lbs.) 50 / 110
Weight of the unit (empty) (kg/lbs.) 62 / 137
Temperature data
Temperature range, 5°C (41°F) above ambient up to (°C / °F) 300 / 572
Temperature variation 1)
at 70 °C (± °C) 0.7
at 150 °C (± °C) 1.8
at 300 °C (± °C) 3.9
Temperature fluctuation (± °C) 0.3
Heating up time 1), 2)
to 70 °C (Min.) 7
to 150 °C (Min.) 28
auf 300 °C (Min.) 49
Recov. time after door was opened for 30 sec.
at 70 °C (Min.) 2
at 150 °C (Min.) 5
at 300 °C (Min.) 12
Air change data
at 70 °C (x/h) 29
at 150 °C (x/h) 32
at 300 °C (x/h) 26
Electrical data
Housing protection acc. to EN 60529 IP 20
Nominal voltage (±10 %) 50 / 60 Hz (V) 230
Nominal power (kW) 1.6
Energy consumption
at 70 °C (W) 230
at 150 °C (W) 544
at 300 °C (W) 1100
1) value without window 2) up to 98 % of the set value
All technical data are specified for units with standard equipment at an ambient temperature of 25 °C and a voltage fluctuation of ±10 %. The temperature data are determinated in accordance to factory standard following DIN 12880 respecting the recommended wall clearances of 10 % of the height, width and depth of the inner chamber.All indications are average values, typical for units produced in series. We reserve the right to alter technical specifications at all times.
Speak to us about your requirements and we'll give you a competitive price. Arrange an onsite visit if you're unsure whether a product offers the best solution for your business's needs.
